How to resolve AdBlock issue?
Oscilloscope News |
16 May 2017 - Rohde & Schwarz is the first oscilloscope manufacturer to offer an integrated arbitrary waveform and pattern generator in the lab class. With the optional generator, all R&S RTO2000 and R&S RTE oscilloscopes can deliver test signals on two analog and eight digital channels, making it possible to test complex circuits in a minimum of space using a single instrument. Even fully automated compliance tests can be performed.
12 May 2017 - TiePie engineering has added a new current clamp to its product portfolio, the Current Clamp TP-CC400. The Current Clamp will allow to measure electrical currents up to 400 A AC/DC. When measuring with this current clamp, there is no need to break a closed circuit or to affect the isolation. The wide jaws allow performing measurements on conductors up to 20 mm.
10 May 2017 - Acute announced its new 100MHz bandwidth high-voltage differential probes: the ADP1100, the ADP2100 and the ADP5100. These probes with good CMRR and low noise floor performance, apply to high-volatge/floating/reference-potential and are better for measuring the MOSFET signal of switching power.
08 May 2017 - Cleverscope launched the new CS448 oscilloscope with four 1kV isolated channels and 200 MHz bandwidth. It is designed for applications where isolation is needed - in particular power electronics. Each channel is isolated from the other, and ground, to 1kV working voltage. The common mode rejection ratio is >100 dB at 50 MHz. The Oscilloscope uses 14 bit ADCs at 500 MSPS to give very good dynamic range, with a noise floor below 100 dBV.
04 May 2017 -Keysight now offers a transmitter and receiver test solution based on the MIPI Alliance’s D-PHY v2.0 and v2.1 specification and C-PHY v1.0 and v1.1 specification and conformance test suite (CTS). The solution also supports MIPI Alliance’s system power management interface (SPMI) specification protocol decoder for battery-operated Internet of Things (IoT) and mobile devices.
03 May 2017 - National Instruments (NI) announced a new 100 MHz, 8-channel oscilloscope that builds on NI’s expertise in high-density and software-designed instruments in PXI. The new PXIe-5172 oscilloscope includes a user-programmable FPGA. Engineers can use LabVIEW to customize this oscilloscope’s firmware, such as adding in-line signal processing or advanced triggering.
12 April 2017 - TiePie engineering announced that Version 1.36 of the Multi Channel oscilloscope software is now available for download. A demo version is also available, which can be used without connecting measuring instruments. For automotive purposes a Crankshaft angle I/O was added. In modern engines, usually a crankshaft sensor is present which generates a periodic signal with a number of cycles per revolution of the engine.
12 April 2017 – Teledyne LeCroy introduces the WaveSurfer 510 oscilloscope, providing 1 GHz bandwidth and 10 GS/s sample rate simultaneously on all 4 channels at a price of $12,900. The WaveSurfer 510 combines the MAUI with OneTouch user interface with powerful waveform processing, in addition to advanced math, measurement, and debug tools, to quickly analyze and find the root cause of problems. The 12.1" touch-screen display of the WaveSurfer 510 is the largest in its class and makes viewing waveform abnormalities fast and easy.
10 April 2017 - SIGLENT’s new SDS1000X-E Series Super Phosphor Oscilloscope is available in one bandwidth, 200 MHz. It has a maximum sample rate of 1 GSa/s and a standard record length of 14 Mpts. For ease-of-use, the most commonly used functions can be accessed with its user-friendly front panel design.
06 April 2017 - Automotive Ethernet has established itself as a standard communications structure. All major manufacturers now depend on this cost-efficient solution for fast data transmission in motor vehicles. With the new IEEE 1000Base-T1 standard, the success story continues. Rohde & Schwarz is the first T&M equipment manufacturer to offer a 1000Base-T1 compliance test solution for the R&S RTO digital oscilloscope.
